Pureit Copper+ Eco Mineral RO+UV+MF has a 7 stage purification system that ensures you get 'Safer than boiled waterTM'. It also removes excess total dissolved salts (TDS) to make the water tastier.
Pureit Copper+ Eco Mineral RO+UV+MF has a storage tank capacity of upto 8 Liters under running water. The process of filling the storage tank is fully automatic. When you take water out of the tank the purification process automatically refills the storage tank.
Pureit Copper+ Eco Mineral RO+UV+MF can purify water upto 24 liters per hour. However, the time taken to purify is influenced by life of the fi¬lters, the input water pressure, and other impurities present in water.
You need to call the Pureit Helpline and order for a Germkill Kit™. A technician will visit your place to replace it, at a nominal cost.
After Pureit Copper+ Eco Mineral RO+UV+MF is installed or whenever the Germkill Kit™ (s) are replaced, discard the fi¬rst cycle of water (8 liters) that is fi¬lled in the storage tank.
In case you cannot dispense water from the spout, fi¬rst check whether the power supply is on. If it is on, then check if there are any fault indicators on, or " SF/GKK” indicator is blinking. Get either the fault resolved or Germkill Kit™ replaced. If none of these indicators are lit up on the indicator panel, then check if the ball valve is closed. If none of these cases are true, then please call Pureit helpline for assistance.
It is not recommended to open and service the device yourself. Call the Pureit helpline if you face any issue which requires servicing and opening the device.
Pureit Copper+ Eco Mineral RO+UV+MF will purify “potable” water for removal of hardness and other impurities to give you safe drinking water. If the input water has impurities normally not present in drinking water (high iron/ turbidity/ microbial contamination etc.) or water is from unknown source (river/lake/pond/borewell etc.) then suitable pre-treatment may be required.
There may be several reasons for this: While the Germkill Kits and the Pre-Sediment Filter have a pre-determined life, depending on your input water quality the Pre-Sediment Filter might need a replacement/cleaning even before the purifi¬er gives you an alert. In such cases, please contact Pureit helpline and get the Pre-Sediment Filter replaced/cleaned. The puri¬fier will communicate the alert only if the purifi¬er is in a switched on condition during the scheduled alert time. Post the completion of the scheduled alert time, Auto Shut off™ of water will be activated automatically for GKK.
Yes. RO technology can remove arsenic, fluoride and nitrates.
It is not recommended to use rejected water for any kind of consumption (drinking or cooking). It can probably be used for gardening or floor cleaning.
Please call Pureit helpline to guide you on any repairs required. You might need to buy the replacement parts at an additional cost.
Turn off the ball valve and switch off the power, if you find any failure. Check for any visually improper fitment and then call Pureit helpline and register a service request.
It is recommended for the stored water to be consumed within 2 days. Water stored for over 2 days should ideally be discarded.
Pureit Copper+ Eco Mineral RO+UV+MF has an indicator panel with SF/GKK indicator that will blink to prompt you to call the Pureit helpline to get the respective GKK changed, whenever the life of the Germkill Kit™ is near expiry (refer to "Understanding LED indicator panel" section of this user manual for further details).
While the Germkill Kit™ and the Pre-Sediment Filter have a pre determined life, you might be required to change the fi¬lters in the interim depending on the quality of your input water. Should the tap flow rate be very low or if it is taking too long for the tank to fi¬ll, then please contact the Pureit helpline to change the membranes. These extra visits will be chargeable as per T&C.
Once the Soft-Touch button is pressed water dispenses for 3 minutes ( 2 minutes if in Warning/ ASO/Fault condition) and it automatically stops dispensing after that. In case you need more water, you need to press the button again. You can stop the flow of water in between by pressing the Soft-Touch button again.
No. It only indicates key electrical faults.
To clean the device body clean dry or wet wiping with 3M foam mop/cloth is recommended. Do not spray water on the device front cover as it may damage the electronic part. Do not use soap or hard cleaning detergents.
Please call the Pureit helpline. A technician will visit you to help resolve the issue.
Please check if the Copper RO Water LED is blinking yellow, if yes then please do wait as device is in Copper Auto-Cleaning Mode. Once the auto-cleaning process is complete you can dispense Copper RO water by pressing the Soft-Touch button. If the copper LED is red, it will not allow dispensing. In such a case check for presence of water from the main line, wait for sometime, then switch o and switch on the purifi¬er again. If the LED is still red, then contact Pureit helpline.
Depending on the amount of water already ¬filled in the tank, you can dispense upto 8 litres of water even without electricity when tank is full by installing manual tap as spare by an authorized service technician. However, Copper RO water can be dispensed only with electricity as Copper is infused in real time.
Consumption of 2 liters of copper charged RO water every day, will add up to approximately 30% of the RDA for copper( for adults, as guided by the Indian Council of Medical Research, ICMR). Copper helps to boost immunity for individuals with defi¬ciency of copper.
Frequently falling sick with signs of inflections are some of the indications of weak immune system.